 
The AMSOIL Dual-Gard By-Pass Oil Filtration System
links two AMSOIL By-Pass Filter Elements together for engines
with sump capacities over 20 quarts. Allows fast and simple servicing
with spin-on elements.
Wear tests have shown particles of contamination
in the sub-20-micron range are most harmful to rings and bearings.
Most trucks are sold with a full-flow filter as their only oil
cleansing unit. A study by the Milwaukee School of Engineering
determined the filtering efficiency of four top selling full-flow
filters compared with a BE-90 AMSOIL Spin-On By-Pass Filter.
Versatility:
Accommodates any two AMSOIL Spin-On By-Pass Filter Elements. Their
unique internal flow director and follower spring system provide
a nonchanneling filter media.
Convenience:
Elements spin on and off for fast, neat filter changes.
Protection:
The stacked disc type by-pass filter has been shown to reduce
piston ring and rod/main bearing wear 75% to 91% (Society of Automotive
Engineers paper 881826).
By-Pass Safety:
A metering orifice inside the mount controls oil flow so that
it never draws more than 10% of the oil pump's capacity. At an
engine speed of 45 mph, the AMSOIL DUAL-GARD By-Pass Filter cleans
all of the oil in the system every 5-10 minutes (depending on
engine RPM, sump size, and oil pump ratio).
The DUAL-GARD Mounting
Kit:
The BMK-12 contains a mount, mounting hardward, a restriction
fitting, and two 3/4" - 16 to 1/4" J.I.C. fittings.
Complete installation instructions are included along with an
additional parts list of plumbing hose and fittings available
from seperately from AMSOIL. Spin-on filter elements, available
in three sizes, should be purchased seperately in pairs based
on sump size or available room in the engine compartment. The
following is merely a guide, since the large the element used,
the less frequently it will need to be changed.
- For a crankcase sump of 15 to 18 quarts
use 2 BE-90 filter elements.
- For a crankcase sump of 15 to 30 quarts
use 2 BE-100 filter elements.
- For a crankcase sump of 15 to 42 quarts
use 2 BE-110 filter elements
Your AMSOIL By-Pass Filters will last twice
as long as your regular engine filter, so change them half as
often.
|
AMSOIL By-Pass
Filter Replacement Chart
|
| Type of Unit |
Stock Number |
Size (Approx.) |
Additional Oil
Needed |
Crankcase Capacity |
Normal
Service Life b |
Applications |
| SINGLE
SPIN-ON ELEMENTS
(Used with BMK-11 or any DUAL REMOTE SYSTEM)
|
BE-90 |
Diam. = 4.5 in.
Height = 6 in.
With Mnt. = 8 in. |
1 qt. |
up to 9 qt. |
25,000
miles or 1 year
(approximately 4 times normal drain interval)
|
Pleasure
Vehicles, Light Trucks and Smaller Commercial Applications |
| BE-100 |
Diam. = 4.5 in.
Height = 8 in.
With Mnt. = 10 in. |
1.5 qt. |
up to 15 qt. |
| BE-110 |
Diam. = 4.5 in.
Height = 10 in.
With Mnt. = 12 in. |
2 qt. |
up to 21 qt. |
| DUAL
SPIN-ON ELEMENT
(Used with BMK-12 DUAL-GUARD)
|
(2) BE-90's |
Diam. = 5 in.
Height = 9.5 in.
With Mnt. = 8 in. |
2 qt. |
15 to 18 qt. |
2 times
normal oil drain interval |
Large
Trucks, Construction, Farm and Industrial Equipment
(minimum sump capacity = 15 qt.)
|
| (2) BE-100's |
Diam. = 5 in.
Height = 9.5 in.
With Mnt. = 10 in. |
3 qt. |
15 to 30 qt. |
| (2) BE-110's |
Diam. = 5 in.
Height = 9.5 in.
With Mnt. = 12 in. |
4 qt. |
15 to 42 qt. |
| LARGE
CANISTER BY-PASS FILTERS |
BE-50 |
Diam. = 7.5 in.
Length = 10 in. |
8 qt. |
15 to 30 qt. |
| BE-75 |
Diam. = 7.5 in.
Length = 15 in. |
12 qt. |
15 to 42 qt. |
a. Filters can be used on sumps of larger capacity but then
require more frequent replacement. Full details on service
life included with filter installation instructions
b. Data determined in a non-turbo
gasoline engine with AMSOIL 100% Synthetic Motor Oil and AMSOIL
Full-Flow Oil Filter. Service life varies in other engines
(turbo and diesel) and with other oils and filters.
NOTES:
-
Special adapters and hardware
may be required for some installations. A universal mounting
bracket is included with the kit, however, custom brackets
may be required depending on your vehicle's equipment options
or personal preferences in mounting locations."
-
Contact AMSOIL INC. Technical Service
for instructions before installing on vehicles with cast aluminum
oil pans.
APPLICATIONS
|
Vehicles with sump capacities up to
and including 15 qts
|
|
Mount
|
Filter (Order
separately unless noted)
|
|
BMK-11
|
Any size AMSOIL Spin-On By-Pass Filter
Element
|
|
BMK-13
|
Any size AMSOIL Spin-On By-Pass Filter
Element
|
| BMK-15 Cummins Diesels (complete
with filters) |
SDF-26 and BE-100 Spin-On By-Pass Filter Element
|
|
BMK-16 International Diesels (complete with filters)
|
SDF-26 and BE-100 Spin-On By-Pass Filter Element
|
|
BMK-17 Duramax Diesels (in GM Pick-ups) (complete
with filters)
|
SDF-26 and BE-100 Spin-On By-Pass Filter
Element
|
|
|
|
Vehicles with sump capacities
greater 15 qts.
|
|
Mount
|
Filter
|
|
BMK-12 Dual Guard
|
Any size AMSOIL Spin-On By-Pass (mount requires 2 filters
and all hoses and fittings)
|
|
